Super silent terminal machine

Ultra-quiet terminal machine

Fully automatic terminal machineIt is still a kind of mechanical product that is used more in our lives. It should be understood! Also, because this kind of product is fully automatic, the hours and minutes used are much more convenient, and the work efficiency can be improved a lot, but no matter what it is, we must learn to maintain it when we use it. If it is well maintained, then we use it. It can also extend its use time when it gets up, but what should we pay attention to when we enter the field for maintenance?

Introduction to the five installation steps of the ultra-quiet terminal machine and the automatic terminal machine: Preparations before the operation of the automatic terminal machine: (1) Check whether the crimping machine and the die are installed firmly, Whether the foot switch and the power socket are plugged in securely. (2) Check whether the power supply voltage is consistent with the specified voltage (220V). (3) Fix the terminal roll and guide the terminal into the die through the guide plate. (4) Adjust the crimping height of the stripping and crimping machine, and manually operate the crimping test terminal. (5) After turning the spindle into place with an open-end wrench, remove the open-end wrench.

Ultra-quiet terminal machine

Automatic terminal machine maintenance precautions

1. It is necessary for the staff to clean the machine every day to remove the dust, debris and remaining oil on the surface of the machine.

The ultra-quiet terminal machine is conductive, so the key point is that too tight will crush the copper wire or directly break the blade. If it is loose, it will make the terminal and This part of the wire is easy to fall off. You can do it more. I think you will be familiar with this one. If you still don’t understand it during the operation, you can call: 0769-87883409 Dongguan Julun Machinery Co., Ltd. We are a professional terminal machine. The wire stripping machine manufacturer will definitely let you understand the debugging method of the terminal machine

2. The crimping part of the automatic terminal machine must be added with butter every week, and evenly spread on the surface of the high-speed bearing and around the press block.

The ultra-quiet terminal machine is installed with the terminal machine that needs to be punched. Use the hexagonal wrench to adjust the feed pressure plate so that the automatic terminal machine can easily pass. Visually check whether the feeding position is suitable. If not, make adjustments. Use an inner hexagon wrench to loosen the feeder locking screw, turn the adjusting rod to adjust until the machine is in normal state, and then tighten the feeder locking screw to start the operation. Test tension: After the adjustment is OK, take the scrap wire and test it, and conduct a tension test. The main reference values are shown in the "Tension Test Comparison Table". The specific operation method is as follows, press the tension test reset button to reset to zero, and set the terminal to be tested The wire is clamped and tested. If the measured tension is not within the standard range, please re-adjust it by the mechanic until it reaches the standard value.

The ultra-quiet terminal machine is installed with the terminal machine that needs to be punched. Use the hexagonal wrench to adjust the feed pressure plate so that the automatic terminal machine can easily pass. Visually check whether the feeding position is suitable. If not, make adjustments. Use an inner hexagon wrench to loosen the feeder locking screw, turn the adjusting rod to adjust until the machine is in normal state, and then tighten the feeder locking screw to start the operation. Test tension: After the adjustment is OK, take the scrap wire and test it, and conduct a tension test. The main reference values are shown in the "Tension Test Comparison Table". The specific operation method is as follows, press the tension test reset button to reset to zero, and set the terminal to be tested The wire is clamped and tested. If the measured tension is not within the standard range, please re-adjust it by the mechanic until it reaches the standard value.

Ultra-quiet terminal machine

3. It is necessary to add oil to the stamping guide rail of the automatic terminal machine once an hour. The smooth oiling hole is on the top of the terminal machine. It is advisable to use 2-3 drops each time. .

What is the technological process of the ultra-quiet terminal machine automatic terminal machine? Turn on the power switch of the automatic terminal, and the power indicator light is on. Pay attention to whether there are obvious abnormal noises inside and outside the machine. If the operation is suspended, ask the maintenance personnel to determine whether maintenance is required. Knife selection and installation: operated by designated personnel. Before installing the tool, you need to manually compare whether the selected tool matches. The tool can only be installed after the comparison is correct. After installing the tool, it must be tested manually. First of all, turn off the power of the automatic terminal machine, press the down touch button, and use the dedicated board to manually move the master and slave wheels to greatly increase the stamping stroke of the terminal press. If the hand does not move, consider whether the pressure is too high or there are other problems, check and adjust to normal. Before operation, check and confirm that the locking screws are not loose.

The daily maintenance precautions of the automatic terminal machine have been introduced here. You can learn more about it, and we should pay more attention to it when we use it. We have better assistance. We should be more careful when using the automatic terminal machine. If you need to buy automatic terminal machines, automatic pipe cutting machines, corrugated pipe cutting machines and other mechanical equipment. Contact us by phone, and we also have punctured terminals, terminal molds, terminal copper strips and other accessories. If you need them, please contact us by phone.

Terminal machine debugging is mainly mold debugging, and this part of the mold is divided into feeding and blade debugging. Generally speaking, there are 4 blades for terminal machine blades, and there are 2 upper blades and 2 lower blades. There are 2 blades, the upper blade is divided into the inner blade and the outer blade.Stripping terminal machineThe same goes for the knife The same, you understand that the next step of debugging is much easier. You must perform manual debugging. One is safe, and we can see whether the crimped terminal meets the requirements in manual debugging. The terminal is crimped. Mainly look at the part of the crimped copper wire, because it is conductive, so the key is too tight, it will break the copper wire or directly break the blade. If it is loose, the terminal and the wire will easily fall off. You should do it more. I think you will be familiar with this one,

Ultra-quiet terminal machine

Ultra-quiet terminal machine

Safety inspection of ultra-quiet terminal machine automatic terminal machine before operation: (1) Confirm that the wrench has been removed. (2) Tighten the round nut after adjustment. The automatic terminal machine runs normally: (1) Press the operating switch to the working position, and the stripping terminal machine motor starts to run. (2) Place the wire in the proper position of the terminal crimping position, and the crimped terminal must be in the middle of the upper and lower die cutters. (3) Step on the foot switch, and the main slider will push down to complete the crimping of the wire and the terminal, and send the next terminal to the crimping position. (4) Repeat the above steps to achieve continuous crimping between the wire and the terminal.